Triton RTA - IP20, load capacity 1200 / 1500 kg, Welded cabinet with removable side panels and rear cover,
Welded frame with removable side and rear panels, IP20, load capacity 1200 / 1500 kg
Description, intended use
Included:
Description, intended use
- 19" upright distribution board with IP20 degree of protection
- The distribution board consists of 4 adjustable vertical latching rails for mounting components (6 in distribution boards deeper than 800 mm)
- Distribution board construction:
- Welded steel frame with removable walls
- Single- or double-leaf doors in the following versions Double-leaf doors in solid sheet metal, perforated (80% and 86% air passage) or glass door versions with 4 mm thick safety glass. They can be mounted at the front or rear of the distribution board
- Preparation for mounting vertical cable routing panels and socket strips, including fixings, on the frame
- Preparation for easy baying of enclosures
- The A5 and A7 versions also have concealed cable entries in the uprights for easy cable routing between the distribution boards
- The maximum permissible load capacity of the individual doors is 20kg
- . 20kg
- These enclosures are designed for the installation of data and telecommunications systems and their distribution systems
- The distribution frame and all removable parts (side and rear panels, doors, etc.) are connected with earthing cables. ) are connected with earthing cables that must be properly secured and plugged in throughout the entire service life of the enclosure
- An M8 screw is located in the base of the enclosure as the main earthing point
- Cable entries with break-out covers are located at the top and bottom
- Conditions of use:
- Offices
- The distribution board is not intended for outdoor use or under conditions that may have a negative impact on its function and that of the installed components (e.g. environment with explosion hazard or environment with a risk of explosion).
- It must be protected against:
- mechanical damage
- improper handling
- use other than that intended for the distributor
- Improper handling means in particular:
- overloading (exceeding the recommended maximum load)
- installation of equipment that may negatively affect the operation and functioning of the distributor or the installed components
- . of the installed components
- Interventions in the distributor construction and its design
- In order to ensure the recommended maximum load, the load must be distributed evenly
- The distributor must be installed on a level surface; any minor unevenness can be levelled out using the levelling feet, which are part of the accessory pack
- In the event that cables are inserted through one of the openings, these can be sealed against dust with the brush strip and fitted with the protective frame (both part of the accessory pack)
- All parts are made from recyclable materials. They must be disposed of in accordance with the applicable regulations after the distributor has been decommissioned
- Toughened safety glass with a thickness of 4 mm, deep-drawn steel sheet
- Reinforced frame: 1.3 mm sheet steel
- Four-point base rail support: 2.5 mm sheet steel
- Triton swivelling lever handles: By replacing the plastic module (not included in the accessory pack), you can choose between a classic and semi-cylindrical locking mechanism. Patent: PUV 2013-27443.
- Wider cabinet corners: The wider cabinet corners are designed for the additional installation of 19" socket strips, so that no space is required in the cabinet for them. Thanks to the well thought-out mounting, extendable servers are not obstructed even in 600 mm wide distribution boards. In addition, the "A5" version (at the end of the enclosure code) has break-out openings in the frame through which cables can be pulled between adjacent enclosures.
- Perforated supports: The openings over the entire height of the uprights correspond to the U spacing of the verticals
- Laser designation of the verticals: sheet steel 2 mm.
- M8 main earthing point
- Plug-in hinges: The standard door hinges can be replaced with plug-in hinges.
- Earthing: All removable parts are interconnected in accordance with the requirements of the relevant standards
- Breakaway panels
- Edging tape: 1 m included in the accessory pack.
- 800 mm wide distributors: 15 - 47 U
- Flex frame: The system enables the installation of adjustable rails at a distance of 19", 21" and 23" with a width of 800 mm.
Included:
- Side panel key 2x
- Door key 2x
- Cage nut M6 16x
- Brush strip 1x
- Edging tape 1m
- Levelling feet 4x
- M10 nut 4x
Free-standing cabinet RTA
Welded skeleton with demountable side panels and back panel, IP 20, loading capacity 1200/1500 kg
Strengthened skeleton
Cold-rolled steel 1,3 mm.
Sliding rail fixed at four points
Cold-rolled steel 2,5 mm.
Tritón handle
By replacing the plastic inlet (not supplied), a classic or half-cylindric lock can be selected. Patent: PUV 2013-27443.
Wider body rails
Wider rails in the body of the cabinet are intended for the additional installation of 19“ power management panels, which afterwards do not occupy space within the cabinet. Thanks to this smart solution of gripping, it does not block the sliding servers even for the 600 mm cabinet type. In addition to this solution, the A5 version (at the end of the cabinet code) is characterized by break-out blanking panels for possible cable input and management in between neighbouring cabinets.
Perforated skeleton rails
Square perforation for the captive nuts alongside the entire height of the rail in the unit span allows additional accessory installation.
Laser unit marking
19“ vertical rails (zinc-coated 2 mm cold-rolled steel) are laser marked at every installation unit.
Main earthing point M8
Hook-on hinges
Standard hinges can be replaced by comfortable-to-use hook-on version.
Bonding
All detachable parts are bonded in accordance with the appropriate standard.
Break-out cable entries
Large amount of cable entries allows comfortable installation cable, also called as patch-rod guiding.
Fringe edge
Supply includes 1 m.
800 mm wide cabinets
15 U – 47 U height
Flex frame
Cabinets with the width of 800 mm have a system, which allows installation of sliding rails in a span of 19“,21“ and 23“.
